Objective
Ideally I'd like to work as a Rig Mechanic or Service Mechanic. It's my passion- the solving of some problems at diverse kind of equipments of drilling and workover rigs. But I'm ready to start from motorhand's position because of temporary lack of proper certificates(I going to graduate all required courses in case considering of myself as applicant).
Experience
Rig Mechanic-Motorman of drilling and workover rigs, Drilling department, Poltava
Petroleum Company (JKX Oil & Gas plc).
July 2013- until present time
Maintain systems and equipment in area of responsibility in compliance with
Maintenance Guides and applicable regulatory requirements.
Using operational knowledge and skills to perform and/or assist in assigned essential functions including but not limited to:
•Starting and stopping main diesel engines, auxiliary engines, pumps, generators, compressors and auxiliary support equipment.
•Replacing dirty lube oils with clean lube oils in various rotating mechanical equipment.
•Reading and monitoring all equipment gauges and recording temperatures and operating hours, maintaining engine log.
•Maintaining oil systems, air systems, water systems, and fuel systems.
•Maintaining hydraulic, pneumatic and lubrication systems.
•Operating various power and hand tools and machinery to perform various inspections, repairs, preventive maintenance and troubleshooting responsibilities.
Foremen Engineer-Mechanic in Department of Well Workover and Remedial Servicing of Poltavagasvidobuvanya NJSC Naftogaz of Ukraine;
March 2012-June 2013
Inspect, analyze, test, measure, repair and perform full or partial overhauls on any of the assemblies and sub- assemblies of undermentioned rigs;
Maintenance and setup of following workover rigs:
Skytop N75 power drive of the diesel engines Caterpillar: CAT 398; CAT 3512; CAT 379; CAT 3412(power station);
AD-520 power drive of the diesel engine Cummins;
A-50; A-60 power drives of the diesel engine YMZ-238,-236;
KORO-80 power drive of the diesel engine V2-D12;
TW-80; TW-100; TW-125 drive of the diesel engines Caterpillar3406;Caterpillar C15; Caterpillar 3408; IRI-100; IRI-125 (band brake winch), IRI-125 (disk brake winch) drive of the diesel engine Caterpillar 3406;
•Managed the moving of rigs;
•Provided support of installation/repair/ inspection of: wellheads, Christmas-trees and blow-out preventers;
•Supervised lift equipment and containers under pressure;
•Carried out the repair of pneumatic system;
•Carried out the repair of hydraulic system;
Maintained the power station on the basis of diesel engines. Such as Caterpillar, Iveco, Detroit,YMZ-238,-236,YAZ-204 etc.
Motorman (Motorhand in crew) in Department of Well Workover and Remedial Servicing of Poltavagasvidobuvanya NJSC Naftogaz of Ukraine;
August 2002-March 2012
•Driving of various types of workover rigs (relocation of rigs).
•Starting and stopping diesel engines, generators, compressors and auxiliary support equipment.
•Replacing dirty lube oils with clean lube oils in various rotating mechanical equipment.
•Reading and monitoring all equipment gauges and recording temperatures and operating hours, maintaining engine log.
•Maintaining oil systems, air systems, water systems, and fuel systems.
•Maintaining hydraulic, pneumatic and lubrication systems.
•Operating various power and hand tools and machinery to perform various inspections, repairs, preventive maintenance and troubleshooting responsibilities.
Fitter-Repairman at overhaul base Poltava branch DC Poltavnaftogazgeologiya, Poltava, Ukraine.
April 2002-August 2002
Repaired and maintained the Christmas-trees, blow-out preventers, valves.
Repairman-fitter of BOPs team, “Krasnoleninskoilgas Service LLC”, v.Poltavskiy, Hanty-Mansiyskiy autonomous district (West Siberia), Russia.
October 2001-March 2002
•Installation/repair of wellheads, Christmas-trees and blow-out preventers;
•Carrying out pressure tests above mentioned equipments on special setup.
Safety Engineer, NII (research (and development) institute) Emalhimmash, Poltava. July 2000-September 2001
Responsible for keeping people free from danger, risk or injury at the workplace, developing of safety programs to minimize losses due to injuries and property damage.
Education
Bachelor's degree, Specialist (5 years), Oil&Gas equipment, National Technical Jury Kondratjuk University, Poltava, Ukraine .
Certification
Graduated the courses of Mechanist & Toolpusher at PoltavaGasvidobuvanya NJSC Naftogaz of Ukraine.
Skils
Diagnostics and Troubleshooting of pneumatic systems.Diagnostics and Troubleshooting of hydraulic systems.Maintenance of Diesel Engines.Pipefitting.Plumbing.Understanding Oilfield Terminology.Equipment Servicing and Maintenance. Reading Drawings.Ordering spare parts.Keen insight of rig operations.Driving(steering)the workover rigs(relocation).
Driving licence:A1(tractor),B(auto)and C(truck);
Computer Skills:advanced user.