Objective
To develop my potentials in the practice of Electrical and Communications Engineering and to share whatever knowledge and skills that I posses in my chosen field in the industry.
Experience
CNOOC CONOCOPHILLIPS
FPSO-Bohai Phase II Development Project
(July 2008 – December 2008) PEP Holder (FIN G6171545U)
Electrical Technician (Commissioning)
• Performed pre-commissioning and commissioning of electrical equipments.
• Performed polarity checked, and contact resistance test.
• Inspected completed installations of Switchgears, Motor Control Center (MCC), Variable Frequency Drive (VFD), motors, cables, transformer's and other electrical equipment for conformance with design and equipment specifications and safety standards..
• Checked all parameters and alarms, charging, discharging and load testing of battery banks
• Performed switching of Ups through battery and by-pass operation.
• Performed modification of various electrical equipments and cables.
• Handled direct preparation of drawings.
• Checked operation data to ensure that the equipment is in its normal operating condition
• Reported to the Senior Electrical Technician all abnormalities found within the area of responsibility
• Perform line check, insulation test and monitoring of motors for no-load and load run.
• Performed pre-commissioning and commissioning of 3.3KV and 10.5 KV switchgears.
• Perform load bank tests for 10.5 KV switchgears.
• Assign in heat tracing and perform loop check and insulation test and monitoring of current and voltage reading of the system.
• Energizing of heat trace equipment and heat trace panel.
• Conduct emergency lighting installation and maintenance.
• Perform Illumination test for both normal and emergency lightings.
• Filled up check sheets and documents
• Closed punch list items
ATLANTIC GULF AND PACIFIC
(March 31, 2008 – June 19, 2008)
Industrial Electrician Engineer Trainee
• Maintain, repair, install and test switch gear, transformers, switchboard meters, regulators and reactors.
• Maintain, repair, test and install electrical motors, generators, alternators, industrial storage batteries and hydraulic and pneumatic electrical control systems.
• Troubleshoot, maintain and repair industrial, electrical and electronic control systems and other related devices.
• Conduct preventive maintenance programs and keep maintenance records. May install, maintain and calibrate industrial instrumentation and related devices.
• Conduit and wiring installation form M.C.C (Motor Control Center) to transformers and motors.
• Performing the duties and responsibilities of industrial electrician, conducting preventive maintenance of power generators.
• Knows how to use electrical apparatus such as clamp meter, megger tester etc. Troubleshooting and repair appliances.
• Installing everything with regards to electrical jobs. Knowledge about fire and safety prevention.
• Lighting wiring installation, motors transformers, AHU, fire alarm, meter base and telecom.
• Installation of PVC Conduit, Distribution Panel and Motor Control. Involved in termination of motor control wiring on MCC panel and also troubleshooting.
HAPPY COMMUNICATIONS, INC. / BIOMETRIX PHILIPPINES CORPORATION – TNRI (September 1, 2006 – February 1, 2008)
Electrical and Telecommunications Engineer
• Read and interpret drawings, blueprints, schematics and electrical code specifications to determine layout of industrial electrical equipment installations.
• Maintain, repair, install and test switch gear, transformers, switchboard meters, regulators and reactors.
• Install, examine, replace or repair electrical wiring, receptacles, switch boxes, conduits, feeders, fiber optic and coaxial cable assemblies, lighting fixtures and other electrical components.
• Test electrical and electronic equipment and components for continuity, current, voltage, and resistance.
• Surveying of Base Station & Customer Premise Equipment (CPE) sites for Cambridge VectaStar 10.5 GHz Wireless Broadband Point to Multipoint radio equipments.
• Wireless Broadband Network Testing and Commissioning.
• Networking Product Testing for both wired and wireless networks.
• Coordination with other contractors regarding network infrastructure equipments and requirements.
• LAN Set Up and Cabling.
• Accompanies sales executives on technical meetings and product demonstrations.
• Renders technical support to clients on repairs and maintenance of all our products
IBIDEN PHILIPPINES INC. (October 11, 2005 – March 11, 2006)
Line Engineer I
• Supervision in the manufacturing of printed circuit board for electronic equipments and assuring that quality standards are followed in the production process.
• Monitoring of control charts and trend charts and analyzes those charts to lessen data variations.
• Design analysis of existing processes for further improvement and modification.
• Conduct root cause analysis of existing problems and construct preventive and corrective actions.
AERIALS AND CABLES INC. (January 2005 – August 2005)
Technician
• Maintenance and Repair, Installation of Power Supply of Generator.
• Maintenance of BTS power supply and batteries.
• Commissioning, installation and troubleshooting of NOKIA BTS Ultrasite 900
• Commissioning and troubleshooting of Eltek rectifiers.
Education
BATANGAS STATE UNIVERSITY
Bachelor of Science in Electronics and Communications Engineering
1999 - 2004
Certification
• Third Generation Wireless Communication
August 3, 2002 at Batangas State University
• Mobile Data Communication Security
September 1, 2002 at Batangas State University
• Structured Cabling
April 3, 2003 at Batangas State University
• Fire Safety Seminar
July 23, 2003 at Shell Philippines Exploration
Alabang Muntinlupa City
• Optic Fiber Technology
November 27, 2003 at Batangas State University
• Seminar on Robotics
March 3, 2004 at Batangas State University
• Failure Modes and Effects Analysis Training
December 1, 2005 at Ibiden Philippines Inc.
• Basic Statistical Process Control
February 13, 2006 at Ibiden Philippines Inc.
Skils
MS Office 2007
MatLab Version 6.0
Electronic Workbench
Nokia Service Terminal